myimportedbeast Posted September 11, 2013 Report Share Posted September 11, 2013 Ok so my celica badge is gold and 2 gold Toyota badges are sold to 25th anniversary but what's the cleanest way to get them off and not leave much residue behind as I'm goin for the debadged look with my stick on plates. Link to comment Share on other sites More sharing options...
Briano Posted September 11, 2013 Report Share Posted September 11, 2013 Front is located with 2 plugs but a gentle pry with a spatchula always works although best to push through from behind The rear just use same spatula and pry it off As for cleaning the gunk comes off alright with a hairdryer Link to comment Share on other sites More sharing options...
sonic Posted September 11, 2013 Report Share Posted September 11, 2013 Lighter fluid works a treat with a hair dryer That sounds like a recipe for a sonic combustion event Use hair dryer to warm up sticky stuff then lighter fluid to remove any residue Will say thou , removing the badges off the rear sometimes leaves marks as the glue damages the lacquer Link to comment Share on other sites More sharing options...
Scottish Storm Posted September 11, 2013 Report Share Posted September 11, 2013 I used dental floss to cut mine off. Then I got as much of the double sided tape of as I could with my fingers and used clay bar to clean the rest off. Came up a treat Link to comment Share on other sites More sharing options...
Jim881 Posted September 11, 2013 Report Share Posted September 11, 2013 (edited) Spatula with masking tape wrapped around it. Then wipe with lighter fluid Sent from my Nexus 10 using Tapatalk 4 Edited September 11, 2013 by Jim881 Link to comment Share on other sites More sharing options...
myimportedbeast Posted September 11, 2013 Author Report Share Posted September 11, 2013 Cheers all that's my task for tomorrow :-D Link to comment Share on other sites More sharing options...
liam_tinny Posted September 11, 2013 Report Share Posted September 11, 2013 A used a bit of fishing wire with a hair dryer and some tar remover Link to comment Share on other sites More sharing options...
skatz114 Posted September 11, 2013 Report Share Posted September 11, 2013 ^^^ I did this too ^^^ then a rub with t-cut & a coat of wax. Sorted Link to comment Share on other sites More sharing options...
Monkey Boy 1 Posted September 12, 2013 Report Share Posted September 12, 2013 Mine came already de-badged Link to comment Share on other sites More sharing options...
Cravo Posted September 12, 2013 Report Share Posted September 12, 2013 I used boiling water on mine. Came off a treat Link to comment Share on other sites More sharing options...
myimportedbeast Posted September 12, 2013 Author Report Share Posted September 12, 2013 Rite I used the hairdryer method and apart from the outer marks of the front badge plus the locating holes back and front all is ok...I'm considering putting my trd badge in the same place as the rear Toyota one and my stick on plate is going over where the front one was. Link to comment Share on other sites More sharing options...
Monkey Boy 1 Posted September 12, 2013 Report Share Posted September 12, 2013 That's all I have on mine, one TRD badge on the front & one on the rear Link to comment Share on other sites More sharing options...
dublet Posted September 12, 2013 Report Share Posted September 12, 2013 That's all I have on mine, one TRD badge on the front & one on the rear You are talking about your car, right? Link to comment Share on other sites More sharing options...
myimportedbeast Posted September 12, 2013 Author Report Share Posted September 12, 2013 Me? Yep I may hav my trd word badge on the rear to cover the holes and my stick on plate on the front to cover the front holes and for style although I will then be left with 4 holes on the front...2 front now plate and 2 wider ones from the Japanese plate holder :-/ I was thinking of some shiny black vinyl to cover those! Link to comment Share on other sites More sharing options...
Recommended Posts