shmotorsport
-
Posts
1,151 -
Joined
-
Last visited
Content Type
Profiles
Forums
Events
Gallery
Club Shop
Collections
Posts posted by shmotorsport
-
-
also why do you care about colour? you cant see them once on the car
-
I would go with the meister r
Can't remember if a member on here had a set on his gen 7 and i'm sure the rears only dropped 20mm or 25mm, unless the ones you posted are a different version of the bc coilovers, so just check on this before going with them
that was on the v1, meister r have now done a v2 which i have and they go really low at the rear. i rubbed so had to raise it up lol
on a second note i have these for sale so if your intrested give me a pm
-
id say the mr2 would win the 0-60 but on track the gt4 would have it
-
-
there was a review a while back and the halfords torque wrench came out on top for it price. also if u can get your hands on a trade card the £80 wrench drops to £50 not sure how much the small one will be reduced buy but any save is a good save
-
just out of interest how did u check the bearing?
-
what about the wheel bearings? have u had them looked at? also does the wobble go away under hard braking? is it just under light breaking that u get the wobble?
-
Do both cars have to be insured at the same time? Does she have a garage? You can change a car on your policy so for 6 months of summer driving she could use the pug and the swap over to the 4x4 for winter driving
-
this is the worst news ive hurd in a while. hope your ok and as u said, lucky it was only one eye
-
Haha yea but an induction kit doesn't do anything but make noise, unless u go for a injen CAI but there big £££. On carbon front I believe ray at rt-performance do one for around £100
-
ill get all in the same size and fitment and just run spacers at the rear. thats the plan anyway. need arches rolled first lol
-
1zz turbo looks like a 350z from the front.
I think there 350 lights
-
correct i want to be able to run the car without spacers. well deffo on the front. so if i can get et 20 wheels they will sit the same as they do now. that way i can just run a spacer on the rear that or i could just buy a larger spacer for the rear but im not a fan of massive spacers. they look gash
-
ive just seen compomotive do et 22
-
I think the 17's look mint mate, have you thought about spending the money on some nice Ksport or BC coil overs ? they you can lower it abit more to fit the wheel and it improives the handling, general rule my S14 mates use it 'If you can fit your fist between the tyre and the arch, then it isnt low enough' Although they are mostly difting nuts lol!
Depends what you plan to do though Im gonna fit coilovers to mine, so gonna keep the 17's so I can lower her more, without having to pay someone to roll my arches. I nearly fitted 18's but then I would have to roll the arche's so its extra cost for no gain :S
meister R all the way. a few of us on here have them and there top quality.
-
I Don't normally like red cars but that is just lush, I think I would spend the money on
a front lip, unless money permits both lol
-
I have 27mm spacers all round and just don't really wanna run any bigger. Not for stress reasons just because as you look through the spokes it looks gash seeing a massive spacer. I have et 48 wheels so would need a spacer around 48mm (never going to look good)
-
Needs an improved description
You can sell anything if it has an awsome description. Capital letters in different colours etc etc usually is enough to turn someone away. I would put down all the answers to the questions I would ask, like was the timing chain done at 100k, the service history has been left blank, why ? How many owners. The usual stuff to start. Bad descriptions make the car look dodgy :S
Weak descriptions wont sell the car most people scroll down to the description first after glancing at the picture and before scrolling back up again to see the piccies.
does the timing chain need to bedone at 100k?
-
12 pictures of the outside of the car, I wanna see engine bay and interior pictures when buying a car.
-
i love 7 spoke wheels and when funds allow i will be looking for a set. i love ultralite atec wheels but i would like a wheel with a low offset so i dont have to run spacers.
looking for about et 5/0 for the rear and et 10 for the front
does anyone know of any wheels with this sort of offset?
cheers
-
Just a knob question... Is impact gun only be avoided for those light or alloy nuts? So if you have a still nuts then it should be fine?
nout actually to do with the nut in this case. the thread had stripped in the spacer which is made from aluminium. but in general you will be better off if you are running steel nuts if someone uses an air gun. BUT you can still strip the thread if overdone
Just drive with four nuts! I've driven with three before and it's fine! Just don't corner too hard...
i cant, wheels wont fit over my BBK
-
Haha yea that was a little odd, I'm happy for u to b gay mate but y did u need to tell us that?
-
seems that i can get the spacer fixed and at a snip of the price of a new one so that has been sent off to freaky parts to be done. hopefully i can get it back asap so i can get back on the raod
-
yea i did get mine done a while ago for £40 summin, i now have mine dropped to the floor so dout ill get on many ramps, do you think i will be able to get on theres as i go to uni in bristol
Where can I get Honda S2000 aerial?
in General Celica Discussion
Posted
the garage had to get me one when i got my s2000 and i believe it was about £30 from honda