Jump to content

How is the "staging" of engines categorised?


Big Lee

Recommended Posts

Hi all.

 

I'm interested to learn how we categorise the staging of engines both mechanically and electronically. Is there a guideline as to what needs to be down to achieve Stage 1, Stage 2 etc?

 

Thanks,

 

Big Lee

Link to comment
Share on other sites

27 minutes ago, Big Lee said:

Makes sense, thanks. Though there might have been a Celica S3GTE guide. 

 

There has been some stuff before for the 3sgte - probably find MR2 forums better on that. A lot of US ones are rev2 3sgte's, though essential the same I assume. 

Example

http://www.atsracing.com/Blog/View/23

 

Following is from KO Racing, which seems to be down so copied and pasted the cached text - again rev2 3sgte

 

Stage 0: 160-165whp; 0-60: ~5.9-6.1; 1/4 mile: ~14.5-14.9

Required:

  • Stock engine
  • Stock turbo
  • Stock exhaust
  • Stock intake
  • Stock intercooler
  • Stock fuel system
  • Stock ecu
  • Stock ignition
  • Stock boost control
  • Stock clutch
  • Stock axles

Recommended/optional:

  • Boost gauge -- the stock unit is approximately useless. Fine for stock boost levels of 9-11psi, but if you plan to raise the boost, or simply want an accurate gauge, the aftermarket mechanical units works great.
  • Synthetic Oil -- this is a high performance engine. Regular oil changes with high quality synthetic fluids will help to keep your engine running at its best.
  • Ensure the ignition components are in proper working order and there are no engine codes present in the factory ECU

Stage 1: 200-230whp; 0-60: ~5.2-5.5; 1/4 mile: ~13.5-14.1

Required:

  • Stock engine
  • Stock turbo
  • Upgraded Exhaust

Both

  • Free Flowing Air intake (Apex'i intake, K&N FIPK, or Cone filter with Vibrant adapter)
  • Stock intercooler (Unplug the engine lid temp sensor to have the IC fan run always with the 'key on')
  • Stock fuel system
  • Stock ecu
  • Stock ignition
  • 15-16psi with boost controller (Either a manual boost controller, or electronic boost control, bypass the factory boost control)
  • Aftermarket boost gauge
  • Fuel cut defenser (factory ecus will typically cut fuel at boost levels above 11psi)
  • Stock clutch
  • Stock axles

Recommended/optional:

  • Upgraded ignition wires and plugs should not make a significant difference in the power output, though reliability and longevity of the parts can sometimes vary from one manufactuer to another. If using OEM Toyota plug wires, they should be changed every 6000 miles or when missing occurs (along with cap and rotor). The NGK spark plugs listed in the ignition components section of our website are one heat range cooler than the OEM specification meaning they can handle hotter engine combustion chamber temperatures better than the OEM heat range units. OEM cap and rotor are recommended as being the best units available for the 3SGTE.
  • Synthetic Oil -- this is a high performance engine. Regular oil changes with high quality synthetic fluids will help to keep your enigne running at its best.

Stage 2: 250-280whp; 0-60: ~4.5-5; 1/4 mile: ~12.8-13.2

NOTE: This is the stage where the factory fuel system limits will be achieved. It will be necessary to monitor your air/fuel ratio with a wideband O2 sensor to safely approach these limits when raising boost. You do not want to run leaner than 12.0:1.

Required:

  • Stock engine
  • Upgraded Turbo

Options:

  • Upgraded Exhaust

Both

  • Free Flowing Air intake (Apex'i intake, K&N FIPK, or Cone filter with Vibrant adapter)
  • Upgraded intercooler (KO Racing High Performance Intercooler Kit)
  • Stock fuel system
  • Stock ecu
  • NGK 4644 plugs or 2667 Iridium plugs gapped at .028", New OEM plug wires or NGK plug wires

·         Either a manual boost controller, or electronic boost controller, bypass the factory boost control
Boost Level:

    • 18psi with boost controller on the upgraded stock or CT20b turbos (Either a manual boost controller, or electronic boost controller, bypass the factory boost control)
    • 15-16psi with KO Racing Turbo kits
  • Aftermarket boost gauge
  • Fuel cut defencer (factory ecus will typically cut fuel at boost levels above 11psi)

Recommended/optional:

  • 270-280whp is the limitation of what the factory fuel system can produce. If you are unable to achieve this power level safely (as tested on a dyno monitoring the Air/Fuel ratio to be no leaner than 11.8:1) there is likely something underperforming in your factory fuel system, ignition system, or ECU. To go beyond this level you will need more fuel which introduces further issues. The factory ECU can control the factory fuel system quite well, but does not do well controlling larger injectors. Piggyback devices such as the S-AFC are strongly recommended to be avoided on the 3SGTE as the potentially engine killing issues associated with the way these devices "tune" the stock computer are too great to risk.

Stage 3: 300-350whp; 0-60: ~4.0-4.5; 1/4 mile: ~12.2-12.5 on pump gas; 350-375whp; 0-60: ~3.5-4.0 seconds; 1/4 mile: 11.9-12.1 on 110 octane race fuel or E85

NOTE: This is the first stage where the factory fuel system and ecu will be upgraded. It is critical that any engine management system that is fully capable of controlling all engine functions be properly and safely tuned by a competent tuner. Not all professional tuners will match this criteria, nor will all amateur tuners not match this criteria. The purpose of engine management is to get you something you weren't able to achieve with the factory computer. That said, there is little to no reason you should have to sacrifice driveability, idle quality, startup quality (cold or hot), throttle tip in response, or any other feature that is not related to simply making more power. Engine management in it's most basic form gives the ability to control much larger than stock sized injectors and thereby facilitate the capability of making a lot more horsepower (as all horsepower is derived by adding commensurate amounts of air and fuel). Tuning at wide open throttle to make XXX hp is probably one of the easiest parts of tuning, though there is the risk of blowing up or otherwise permanently damaging the engine, relatively speaking this is one of the shortest duration parts of tuning. This component of tuning comprises typically 20% or less of the time required to do a full tune in my experience.

Selecting the fuel system and turbo size at this stage should be done in such a way as to allow you to make the power you desire with some room to spare. In the case of the turbo, selecting the smallest turbo option that will support your horsepower goal will allow for the best transient response and quickest spool relative to your goal in most cases. On the fuel injector side: tuning a set of 680cc injectors or tuning a set of 880cc injectors will not change the effort involved, but the larger injectors will tend to run lower duty cycle and therefore possibly have some benefit in life. Smaller injectors typically will have a better spray pattern than large injectors, but as long as the idle quality is good, there can be negligible difference in the actual injector size from 880-1200 for example. If you, howeever, go to a very large injector, the resolution at idle will suffer and the injector may have so little time to open and close that it will not reliably be able to do so (typically seen with 2000+ cc injectors on 2.0 or 2.2L engines) and will require a higher idle speed (1200-1300 rpm in many cases).

This is also the first stage at which it is recommended to upgrade the clutch vs. OEM. The OEM clutch can handle this power level, but will not have the life or resilience of heavier duty aftermarket options. It is not uncommon to get a couple of drag strip launches at this power level on the stock clutch and then have it haze and go up in dust on the third try. Your mileage may vary. The clutch most commonly selected at this point is the ACT HD pressure plate with either the 6 puck or the organic full face disk. The 6 puck is rated at 499ftlbs, and the full friction disk is rated at 383ftlbs. These are flywheel measurements and given the common disparity between HP production and torque production, it becomes a happy coincidence that typically those torque ratings can be used as a rough guide for the equivalent wheel horsepower maximum the clutch is capable of also. For example: the full face friction ACT clutch rated at 383ftlbs of torque at the flywheel is often good to about 380 hp as measured at the wheels on a chassis dyno.

Required:

  • Stock engine
  • Upgraded Turbo

Options:

Both

Boost Level:

    • 18-20psi with KO Racing Turbo kits on pump gas
    • 20-22psi with KO Racing Turbo kits on race gas
  • Aftermarket boost gauge
  • ACT TM1-HDR66 puck clutch or ACT TM1-HDSS full face clutch

Recommended/optional:

  • 22psi is the typical limit of the factory Gen 2 3sgte head gasket. 18-20 psi tends to be the limit on supreme pump gasoline between 91 and 93 octane. If you are unable to achieve this power level safely (as tested and tuned on a dyno monitoring the Air/Fuel ratio to be no leaner than 11.5:1, and knock levels in a safe range) there is likely something underperforming in the engine mechanically, or in the ignition system. It is best to seek out a reputable and experienced tuner to extract the most safe power as your engine combination can achieve. Pushing this kind of power level can be safe and reliable but will likely live a shorter time than 100% stock setups. You will find out the limitations of your stock system when pushing up to this power level more than likely. The factory fuel lines will still be ok at this level with the upgraded pump and injectors. Tuning with the EMS will also allow the ability to do a race fuel tune without changing anything else which should yield 350-380whp at 22psi on 110 octane fuel.

 

 

 

 

Edited by digs
  • Thanks 1
Link to comment
Share on other sites

×
×
  • Create New...

Important Information

We have placed cookies on your device to help make this website better. You can adjust your cookie settings, otherwise we'll assume you're okay to continue.